Mechanical Electrical Flashings
Photo Album Gallery Place Holder - Please wait while the Photo Album loads. If the album does not show, please refresh the page to try again.
MEF-1 Rigid Conduit Flashings
MEF-2A Liquid Tight Flexible Conduit Flashings
MEF-2A1 Liquid Tight Flexible Conduit Flashing
MEF-2A2 Liquid Tight Flexible Conduit Flashing
MERS MECHANICAL & ELECTRICAL ROOF SUPPORTS
MEF-4A "B" Vent Flashings
MEF-9 Modcom Gas Pipe Flashing
MEF-AE1 Rigid Conduit Flashing
MEF-1 Rigid Conduit Flashings
Thaler MEF-1 Rigid Conduit Flashing consists of a metal flashing sleeve with integral deck flange, screw fastened removable cap (fractional sizes), EPDM Triple Pressure Grommet Seal, and EPDM Base Seal. Available in aluminum, copper and stainless steel.
MEF-AE1 Rigid Conduit Flashing
Thaler MEF-AE1 Rigid Conduit Flashing consists of a metal flashing sleeve with integral deck flange, screw fastened removable cap (for odd sizes), EPDM Triple Pressure Grommet Seal, and EPDM Base Seal. Available in aluminum, copper and stainless steel.

Recommended Use: For rigid mechanical or electrical conduit penetrating the roof.
Recommended Use: MEF-2A, MEF-2A1, MEF-2A2
MEF-2A Liquid Tight Flexible Conduit Flashings
Thaler MEF-2A Liquid Tight Flexible Conduit Flashings consist of a gooseneck shaped aluminum flashing pipe sleeve with integral deck flange, EPDM End Cap Seal and EPDM Base Seal. Each seal is provided with two holes, one for liquid tight flexible conduit and the other for a small diameter auxiliary wire for air handling units (optional).
MEF-2A1 Liquid Tight Flexible Conduit Flashing
Thaler MEF-2A1 Liquid Tight Flexible Conduit Flashings consist of a gooseneck shaped aluminum flashing pipe sleeve with integral deck flange, EPDM End Cap Seal and EPDM Base Seal. Each seal is provided with two holes, one for liquid tight flexible conduit and the other for a small diameter auxiliary wire for air handling units (optional).
MEF-2A2 Liquid Tight Flexible Conduit Flashing
Thaler MEF-2A2 Liquid Tight Flexible Conduit Flashings consist of a gooseneck shaped aluminum flashing pipe sleeve with integral deck flange, EPDM End Cap Seal and EPDM Base Seal. Each seal is provided with two holes, one for liquid tight flexible conduit and the other for a small diameter auxiliary wire for air handling units (optional).
MEF 2C
Thaler MEF 2C Liquid Tight Flexible Conduit Flashing consisted of gooseneck shaped copper double walled flashing.

Recommended Use: For liquid tight flexible conduit from 1/2" to 2 1/2". (increments of 1/2").
MEF-AG2
MEF-3A Hot Pipe Flashing
Thaler MEF-3A Hot Pipe Flashing consists of a metal flashing sleeve with integral deck flange, and matching two piece, friction fit collar. The flashing sleeve is typically supplied 6" (152 mm) larger than the hot pipe diameter to accommodate 4" (102 mm) of mineral wool insulation (by others) and 2" of air space.

Recommended Use: For hot pipes used in connection with steam heating, chimney pipes and similar applications.
MEF-9 Modcom Gas Pipe Flashing
Thaler MEF-9 Modcom Gas Pipe Flashings consist of a metal flashing sleeve with perforated collar and integral deck flange, and removable collar with EPDM Triple Pressure Grommet Seal. Available in aluminum, copper and stainless steel.

Recommended Use: Suitable for gas pipe and similar applications.
MEF-4A "B" Vent Flashings
Thaler MEF-4A "B" Vent Flashing consists of an aluminum flashing sleeve with integral deck flange, matching two piece collar, and EPDM Triple Pressure Grommet Seal. Available in aluminum only.

Recommended Use: For "B" Vents used in connection with gas heaters. Not intended for "hot pipes".